Download 04.07.16 Bulletins.wartsila.com Bulletins File Wfi 4602n100 05gb PDF

Title04.07.16 Bulletins.wartsila.com Bulletins File Wfi 4602n100 05gb
TagsFuel Oil Petroleum Chemical Substances Hydrocarbons Motor Oil
File Size436.2 KB
Total Pages14
Table of Contents
                            4602N100_05gb_noatt
	Enclosure
	Contacts
V92A0670_000_l_modified
                        
Document Text Contents
Page 1

DATA &
SPECIFICATIONS

For your information

Engines concerned
WÄRTSILÄ® 46 and 46GD engines

Reference
02 Fuel, lubricating oil, cooling water

Introduction
Updated lubricating oil specification for
WÄRTSILÄ® 46 and 46GD engines.

Validity / Issue
Until further notice. Replacing issue 4,
dated 31-Aug-2012.

Wärtsilä Finland Oy Services 24 hrs Tel: +358 10 709 080
P.O. Box 252 (Tarhaajantie 2) Switchboard Tel: +358 10 709 0000
FIN-65101 Vaasa, Finland

Issue 5, 26 May 2016

Lubricating oils for WÄRTSILÄ® 46
and 46GD engines
Information to Operators and Owners of installations
concerned

4602N100Wärtsilä 4-stroke
Technical Services

Page 2

DATA & SPECIFICATIONS

4602N100, Issue 5, Page 2 / 2 + 12

Enclosure
Requirements and oil quality 4V92A0670, revision l, 12 pages.

Contacts
For questions about the content of this bulletin, or if you need Wärtsilä assistance,
services, spare parts and/or tools, please contact your nearest Wärtsilä representative.

If you don’t have the contact details at hand, please follow the link:
www.wartsila.com/contact

© 2016 Wärtsilä Finland Oy – All rights reserved
No part of this publication may be reproduced or copied in any form or by any means (electronic, mechanical, graphic, photocopying, recording,
taping or other information retrieval systems) without the prior written permission of the copyright holder. Wärtsilä Finland Oy makes no
representation, warranty (express or implied) in this publication and assumes no responsibility for the correctness, errors or omissions for
information contained herein. Information in this publication is subject to change without notice.
Unless otherwise expressly set forth, no recommendation contained in this document or any of its appendices is to be construed as provided
due to a defect of the product, but merely as an improvement of the product and/or the maintenance procedures relating thereto. Any actions
by the owner/operator as a result of the recommendations are not covered under any warranty provided by Wärtsilä and such actions will
thus be at the owners/operators own cost and expense.
NO LIABILITY WHETHER DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL, IS ASSUMED WITH RESPECT TO THE
INFORMATION CONTAINED HEREIN. THIS PUBLICATION IS CONFIDENTIAL AND INTENDED FOR INFORMATION PURPOSES
ONLY.

http://www.wartsila.com/contact

Page 7

Page

5 (10)

Document No

4V92A0670

Rev

l





Chevron (Texaco
+ Caltex)

Delo 1000 Marine 40
Taro 12 XD 40
Taro 20 DP 40
Taro 20 DP 40X

SAE 40
SAE 40
SAE 40
SAE 40

12
12
20
20

A,B,F,G
A,B,F,G
A,B,F,G
A,B,F,G

Page 8

Page

6 (10)

Document No

4V92A0670

Rev

l







SUPPLIER BRAND NAME VISCOSITY BN FUEL
CATEG.

Conqord Oil Q8 Marine D 1000 SAE 40 SAE 40 12 A,B,F,G

ENI S.p.A. Cladium 140 S SAE 40 14 A,B,F,G

ExxonMobil Delvac 1640
Mobilgard ADL 40
Mobilgard 412
Mobilgard 1 SHC

SAE 40
SAE 40
SAE 40
SAE 40

12
12
15
15

A,B,F,G
A,B,F,G
A,B,F,G
A,B,F,G

Indian Oil
Corporation

Servo Marine 1040
Servo Marine 1540
Servo Marine 2040

SAE 40
SAE 40
SAE 40

10
15
20

A,B,F,G
A,B,F,G
A,B,F,G

Irving Blending &
Packaging

Irving Marine MTX 1540
Irving Marine MTX 2040

SAE 40
SAE 40

15
20

A,B,F,G
A,B,F,G

Petrobras Marbrax CCD-415
Marbrax CCD-420

SAE 40
SAE 40

15
20

A,B,F,G
A,B,F,G

Shell Gadinia Oil 40 SAE 40 12 A,B,F,G

Statoil MarWay 1040 SAE 40 10,6 A,B,F,G

Total / Lubmarine Disola M 4012
Disola M 4015
Disola M 4020
Caprano M 40

SAE 40
SAE 40
SAE 40
SAE 40

12
14
20
14

A,B,F,G
A,B,F,G
A,B,F,G
A,B,F,G



WÄRTSILÄ 46: OPERATION ON HEAVY FUEL OR CRUDE OIL


Modern trunk piston diesel engines are stressing lubricating oil heavily e.g. due to low
specific lubricating oil consumption. Also ingress of residual fuel combustion products into
the lubricating oil can cause deposit formation on the surface of certain engine components
resulting in severe operating problems. Due to these facts it is essential to use only
lubricating oils with modern additive technologies having good compatibility between fuel
and lubricating oil.

WÄRTSILÄ 46GD: OPERATION ON NATURAL GAS, HEAVY FUEL OR CRUDE OIL AS
MAIN FUEL AND HEAVY FUEL OR CRUDE AS PILOT FUEL

If heavy fuel or crude oil is used as pilot / back-up fuel even only occasionally in the Wärtsilä
46GD engine, lubricating oils with BN of 30 55 shall be used.

Table 2.


Validated system oils - fuel categories C, D and G, included in the Table 2 recommended in
the first place when operating Wärtsilä 46 engines on heavy fuel or on crude oil having high
sulphur content in order to reach full service intervals. BN 50 - 55 lubricating oils are
preferred in the first place. The oils included in the Table 2 or 3 shall also be used in the
Wärtsilä 46GD engine if heavy fuel or crude oil is used as pilot / back-up fuel.

Page 13

Page

11 (10)

Document No

4V92A0670

Rev

l







SUPPLIER BRAND NAME VISCOS-
ITY

BN FUEL
CATEG.

Petron Petromar XC 3040
Petromar HF 3040

SAE 40
SAE 40

30
30

A,B,C,D,G
A,B,C,D,G

Petronas
Lubricants
International

Disrol 300 SAE 40 SAE 40 30 A,B,C,D,G

Shell Argina T 40 SAE 40 30 A,B,C,D,G

Sinopec TPEO 4030 SAE 40 30 A,B,C,D,G

SK Lubricants Supermar 30TP40 SAE 40 30 A,B,C,D,G

Total / Lubmarine Aurelia TI 4030 SAE 40 30 A,B,C,D,G


Before using a lubricating oil not listed in Tables 1 - 3, the engine manufacturer must be
contacted. Lubricating oils that are not validated have to be tested according to engine
manufacturer’s procedures.

Lubricating oil companies listed above along with other possible manufacturers and
distributors undertake all responsibility for the performance of their validated lubricating oils
in service to the exclusion of any liability of any Wärtsilä company belonging to Wärtsilä
group. Further, they shall indemnify, compensate and hold harmless Wärtsilä and
companies belonging to Wärtsilä group from and against any claims, damages and losses
caused by the lubricating oils in question.



APPROVED LUBRICATING OILS FOR ABB VTR-TURBOCHARGERS


SPECIAL LOW FRICTION SYNTHETIC OILS: CHANGE INTERVAL: 1500 hours
(ABB’s List 2b)

MANUFACTURER BRAND NAME VISCOSITY
cSt at 40 °C

VISCOSITY
cSt at 100
°C

VI

Shell Corena S4 P 68 68 8,5 94

Sinopec Greatwall 4506N68
Synthetic Compressor Oil

64,7 10,0 138



SPECIAL LOW FRICTION SYNTHETIC OILS: CHANGE INTERVAL: 2500 hours
(ABB’s List 3b)

MANUFACTURER BRAND NAME VISCOSITY
cSt at 40 °C

VISCOSITY
cSt at 100 °C

VI

BP Enersyn TC-S 68 68 8,5 98

Chevron (Texaco
+ Caltex)

Cetus PAO 68 68 10,3 138

Castrol Aircol SR 68 68 10,5 142

ENI S.p.A. Dicrea SX 68 71,6 10,5 134

ExxonMobil Rarus SHC 1026
SHC 626

66,8
69,9

10,4
10,9

144
147

Petrogal Galp Lubarep PRS68 65,8 10,4 146

Shell Corena S4 R 68 68 10,2 135

Page 14

Page

12 (10)

Document No

4V92A0670

Rev

l





Total / Lubmarine Barelf SM 68 73,8 11,4 147



LUBRICATING OILS FOR ENGINE TURNING DEVICE


Based on the turning device manufacturer’s instructions EP-gear oils having viscosity of 414
- 506 cSt at 40 °C = ISO VG 460 are normally considered as suitable lubricating oils for
turning device. The following products are fulfilling the requirements:



LUBRICATING OILS FOR ENGINE TURNING DEVICE

SUPPLIER BRAND NAME VISCOSITY
cSt at 40 °C

VISCOSITY
cSt at 100 °C

VISCOSITY
INDEX (VI)

BP Energol GR-XP 460 460 30,5 95

Castrol Alpha SP 460 460 30,5 95

Chevron (Texaco
+ Caltex)

Meropa 460 460 31,2 97

ENI S.p.A. Blasia 320 300 23,0 95

Fuchs Renolin CLP 460 460 30,4 95

ExxonMobil Mobilgear 600 XP 460 460 30,6 96

Shell Omala S2 G 460 460 30,8 97

Total / Lubmarine Carter EP 460 470 30,3 93



LUBRICATING OILS FOR GOVERNOR / ACTUATOR


An oil of viscosity class SAE 30 or SAE 40 is suitable and usually the same oil can be used
as in the engine. Turbocharger oil can also be used in the governor. At low ambient
temperature it may be necessary to use a multigrade oil (e.g. SAE 5W-40) for better
governor response during start-up. Oil change interval: 2000 service hours.

Similer Documents